How much does a concrete bull float cost

Average costs: You’ll pay about $100 to $125 for a 4-foot magnesium bull float with bracket, and $18 for a 14-inch magnesium hand float. The price of wood floats varies, depending on the type of wood used, but will generally be lower than the cost of magnesium.

Can you finish concrete without a bull float?

A bull float is used to level and smooth freshly poured concrete. Concrete used for visible projects, such as driveways, patios and sidewalks, often requires finishing. … A bull float is a tool used for finishing concrete.

What is the best concrete float?

Magnesium. Although they are slightly weaker than their aluminum counterparts, magnesium floats are lighter and are the most popular choice among professionals. Magnesium smooths the surface of fresh concrete and opens the pores for proper evaporation, all without pulling the surface like a wood or resin tool.

Can you bull float concrete too much?

If you can’t reach the entire slab from the edges with a darby, rent a bull float and handle to use instead. Two passes over the surface with the darby are enough. Overworking the concrete will draw too much cement and fine sand to the top and create a weak surface.

How long do you wait to bull float concrete?

Darbying or bull floating should be done immediately after “screeding”, or after the concrete has been tamped if tamping was done. This process should be finished before excess moisture or bleedwater appear on the surface.

What is the difference between a Fresno and a bull float?

What it is: The fresno may look similar to the bull float, but its blade is made of tempered or “blue” steel. The fresno should only be used following the bull float. Purpose: The fresno is applied after the bull float to better seal the surface of the slab.

What can I use instead of a bull float?

Fresnos are used for troweling slabs that do not require a hard trowel surface. A Fresnos will speed up the troweling process. Fresnos should not be used as bull floats. Troweling can also be accomplished by machine.

How long does it take to bleed water to evaporate?

This creates a blister and when that pocket of water evaporates it will become an air cavity. The thin layer then will just flake off in a matter of time. By just waiting 30 minutes, depending on weather conditions, your bleed will be gone by itself and be ready for proper finishing.

What happens if you dont float concrete?

More often, premature finishing or improper first (bull floating) or second floating results in trapping rising bleed water and air below the top surface of the concrete (Image 2). When this occurs, the resulting weak or soft zone below the surface causes the top surface of the concrete to flake or scale off.

Can you make a bull float?

Professional bull floats can be made of aluminum or magnesium and are meant for long term and continuous use. It is possible for an amateur to construct an inexpensive unit that will perform the same task.

Article first time published on

Why is it called a bull float?

Probably takes its name from the definition of bull—to make one’s way with driving force (Webster’s New World Dictionary). Spend a few minutes on a hot day smoothing concrete with a bull float, and you’ll get the idea.

How long does it take concrete to fully cure?

Concrete typically takes 24 to 48 hours to dry enough for you to walk or drive on it. However, concrete drying is a continuous and fluid event, and usually reaches its full effective strength after about 28 days.

How many times should you float concrete?

Push the bull float in one direction only across the concrete, keeping its front edge slightly above the surface by raising or lowering the handle. Two or three times is enough. Don’t overwork the concrete or you’ll weaken it by drawing too much sand and cement to the surface.

What does a Fresno trowel do?

Purpose: Fresno trowels are designed to attach to long extension handles so finishers don‘t have to walk out on the slab. They permit rapid work over large areas, such as driveways, but do not achieve the same degree of compaction possible with hand trowels.

Can you make a concrete float?

Most people think concrete can’t float because it’s too heavy. But if concrete is shaped in the right way and light enough, it can float just like any other material. Any object, including concrete, will float if it’s less dense than the water it’s placed in.

What's the difference between a trowel and a float?

A float has a thicker base than a trowel and is usually made of plastic, sponge, rubber, wood or magnesium – a lightweight pale grey metal. It’s used to even up the surface on plaster or concrete, make it firmer and give whatever texture is required. The finish will depend on the float chosen.

How do you smooth concrete after it dries?

1. Remove all imperfections on the surface.
2. Vacuum up all debris and apply the adherent.
3. Apply a new layer of concrete.
4. Sand the surface and wash the concrete.
5. Apply a layer of vitrifier to protect the concrete.

What is trowel used for?

A trowel is a small garden tool which you use for digging small holes or removing weeds. A trowel is a small tool with a flat blade that you use for spreading things such as cement and plaster onto walls and other surfaces.

What is a trowel finish?

Trowel-finished concrete floors are seamless surfaces that recreate the concrete effect. They can be applied to any kind of surface, indoor and outdoor, horizontally or vertically. The decorative effects that can be obtained with a trowel-finished concrete surface are several and always customizable.

What is Mag floating concrete?

A mag float is simply a flat piece of magnesium or aluminum attached to a handle. The tool allows the user to float concrete at his or her desired pressure and angle. Mag floats are also available in a wide range of lengths and widths.

How much does it cost to finish concrete?

To have concrete poured and finished, it will cost $2.52 to $2.60 per square foot for the labor, and $2.83 to $3.57 per square foot for the concrete itself.

What happens if it rains right after pouring concrete?

HOW DOES RAIN AFFECT CONCRETE? Rain falling on top of freshly laid concrete can damage the surface and compromise a level and floated finish. Even worse, if too much extra water works its way into the concrete mix, this can result in weak concrete overall.

Is bleeding in concrete bad?

Some bleeding is normal but excessive bleeding can be problematic. The way you work that bleed water can affect the durability of your products. The biggest factor in bleed water rates is the water-to-cement ratio. A higher ratio can lead to excessive bleeding.

What happens if you overwork concrete?

Never overwork or over finish the surface of any exposed concrete slab. This brings too much fine material to the surface, works out the designed air entrainment*, and will weaken the surface of the slab leaving the top of slab more vulnerable to freeze/thaw damage and sheet scaling*.

What is a concrete screed?

In a nutshell, a concrete screed is a straightedge tool that levels and smoothens the surface of freshly poured concrete. … As a screed passes over wet concrete, it pushes large aggregate down and brings “creme” to the surface. They leave concrete surfaces smooth, flat, and free from any deformities.

What is wooden float?

A woodworking float (more rarely used in silversmithing), also called a planemaker’s float, is a tapered, flat, single cut file of two types: edge float and the flat sided float which are traditional woodworking tools generally used when making a wooden plane. … Floats are similar to rasps and files.

Why do you power float concrete?

A power float is a hand-operated machine used to produce a smooth, dense and level surface finish to insitu concrete beds. Power floating eliminates the time and materials needed to apply a finishing screed and is quicker and less labour-intensive process than hand trowelling.

Can you drive on concrete after 3 days?

Your new concrete is designed to reach 90% of its full strength potential after 7 days, so feel free to drive your personal vehicle on it then. It will take additional time before you can drive or park heavy equipment or machinery on your newly poured concrete, so make sure to wait at least 30 days.

Does rain hurt new concrete?

If the rain occurs when the concrete is fresh (about 2-4 hours after mixing), the surface should be protected from the rain. … If the concrete has stiffened to the point where it is ready for grooving and grinding (typically 4-8 hours after mixing), damage due to rain is usually no longer a concern.

Does it take 100 years for concrete to cure?

Does concrete take 100 years to cure? No, this is a bit of a myth with the concrete industry. While concrete does continue to harden indefinitely, pore moisture has to drop below a certain level at some point and this isn’t typically 100 years.

When should you start curing concrete?

The best practice is to cure the concrete shortly after the chemical reaction has started that hardens the concrete. Concrete should not be allowed to dry fast in any situation, and the curing conditions must be maintained during the first 24 hours or at least until the final setting time of cement has passed.